The impact of matrix microstructure and reinforcement size (micron vs. nano-size) on the compressibility of Al-SiC powder mixtures and hardness of Al/SiC composites

Document Type : Research Paper

Authors

1 Department of Materials Science and Engineering, Shiraz University of Technology, Shiraz, Iran

2 School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran, Iran

Abstract

In the present study, four series of Al-6061/SiC composites synthesized via powder metallurgy technique were used to investigate the impact of the matrix grain size and/or the size of reinforcing particles on enhancing the compressibility of powder mixtures and hardness of the composites. In two series, the as-received Al powders have micron-sized grains mixed with either nano-sized or micron-sized SiC particles. For the other two series, the Al powders were initially milled to convert their grain size to nano-scale before mixing with either nano-sized or micron-sized SiC particles. The powder mixtures containing 1, 2, and 3 vol.% of SiC particles were cold pressed and hot extruded. The decreased compressibility in all of the four series of Al/SiC powder mixtures with increased SiC content attributed to the enhanced portion of the hard and non-deformable SiC particles in the powder mixtures resulting in a reduced degree of plastic deformation. Increment the SiCn content from 0% to 3% resulted in a significant increase in the microhardness of 20h planetary ball milled powders accompanied with decrease compressibility of powders. The composites were subjected to Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), and X-ray diffraction (XRD) studies as well as density and hardness measurements. Metallographic studies and density measurements confirmed significant densification with no indication of voids in the samples’ microstructures after hot extrusion. The results revealed that matrix microstructure, as compared with the size of the reinforcing particles, was more influential in enhancing the powder compressibility and composite hardness.  

Keywords


  1. Anvari SZ, Enayati MH, Karimzadeh F. Wear Behavior of Nanostructured Al-Al3V and Al-(Al3V-Al2O3) Composites Fabricated by Mechanical Alloying and Hot Extrusion. Journal of Ultrafine Grained and Nanostructured Materials. 2020 Dec 28;53(2):135-45.
  2. Kumar A, Pal K, Mula S. Simultaneous improvement of mechanical strength, ductility and corrosion resistance of stir cast Al7075-2% SiC micro- and nanocomposites by friction stir processing. Journal of Manufacturing Processes. 2017;30:1-13.
  3. Moazami-Goudarzi M, Akhlaghi F. Wear behavior of Al 5252 alloy reinforced with micrometric and nanometric SiC particles. Tribology International. 2016;102:28-37.
  4. Mosleh-Shirazi S, Akhlaghi F, Li D-y. Effect of SiC content on dry sliding wear, corrosion and corrosive wear of Al/SiC nanocomposites. Transactions of Nonferrous Metals Society of China. 2016;26(7):1801-8.
  5. Moazami-Goudarzi M, Akhlaghi F. Effect of SiC nanoparticles addition on densification of commercially pure Al and 5252 Al powder compacts. Journal of Ultrafine Grained and Nanostructured Materials. 2021 Dec 27;54(2):121-30.
  6. Mosleh-Shirazi S, Akhlaghi F. Theoretical and Experimental Investigations on Shear Strength of Al 6061/Gr Nanocomposites Produced by Powder Metallurgy. Journal of Advanced Materials and Technologies. 2019 Dec 21;8(3):1-1.
  7. Liu YQ, Cong HT, Wang W, Sun CH, Cheng HM. AlN nanoparticle-reinforced nanocrystalline Al matrix composites: Fabrication and mechanical properties. Materials Science and Engineering: A. 2009;505(1-2):151-6.
  8. Kang Y-C, Chan SL-I. Tensile properties of nanometric Al2O3 particulate-reinforced aluminum matrix composites. Materials Chemistry and Physics. 2004;85(2-3):438-43.
  9. Akhlaghi F, Mosleh-Shirazi S. Effect of SiC Nanoparticles Content and Milling Time on the Characteristics of Al/SiC Nanocomposite Powders Produced via Mechanical Milling. Advanced Materials Research. 2013;829:505-9.
  10. Gostariani R, Ebrahimi R, Asadi Asadabad M. The Study of Hot Deformation Behavior of Mechanically Milled and Hot Extruded Al–BN Nanocomposite. Transactions of the Indian Institute of Metals. 20171;71(5):1127-36.
  11. Mosleh-Shirazi S, Akhlaghi F. Tribological behavior of Al/SiC and Al/SiC/2 vol%Gr nanocomposites containing different amounts of nano SiC particles. Materials Research Express. 2019;6(6):065039.
  12. Skrzekut T, Kula A, Blaz L, Wloch G, Sugamata M. High-strength and thermally stable Al – CeO2 composite produced by means of mechanical alloying. International Journal of Materials Research. 2014;105(3):282-7.
  13. Mahdavi Jafari M, Soroushian S, Khayati GR. Hardness optimization for Al6061-MWCNT nanocomposite prepared by mechanical alloying using artificial neural networks and genetic algorithm. Journal of Ultrafine Grained and Nanostructured Materials. 2017 Jun 1;50(1):23-32.
  14. Mosleh-Shirazi S, Akhlaghi F, Li DY. Effect of graphite content on the wear behavior of Al/2SiC/Gr hybrid nano-composites respectively in the ambient environment and an acidic solution. Tribology International. 2016;103:620-8.
  15. Ahamed H, Senthilkumar V. Role of nano-size reinforcement and milling on the synthesis of nano-crystalline aluminium alloy composites by mechanical alloying. Journal of Alloys and Compounds. 2010;505(2):772-82.
  16. Jia DC. Influence of SiC particulate size on the microstructural evolution and mechanical properties of Al–6Ti–6Nb matrix composites. Materials Science and Engineering: A. 2000;289(1-2):83-90.
  17. Fu MW, Tham YW, Hng HH, Lim KB. The grain refinement of Al-6061 via ECAE processing: Deformation behavior, microstructure and property. Materials Science and Engineering: A. 2009;526(1-2):84-92.
  18. Fogagnolo JB, Ruiz-Navas EM, Robert MH, Torralba JM. 6061 Al reinforced with silicon nitride particles processed by mechanical milling. Scripta Materialia. 2002;47(4):243-8.
  19. Test Method for Density of Powder Metallurgy (PM) Materials Containing Less Than Two Percent Porosity. ASTM International.
  20. Basiri Tochaee E, Madaah Hosseini HR, Seyed Reihani SM. On the fracture toughness behavior of in-situ Al-Ti composites produced via mechanical alloying and hot extrusion. Journal of Alloys and Compounds. 2016;681:12-21.
  21. Fogagnolo JB, Ruiz-Navas EM, Robert MH, Torralba JM. The effects of mechanical alloying on the compressibility of aluminium matrix composite powder. Materials Science and Engineering: A. 2003;355(1-2):50-5.
  22. Moazami-Goudarzi M, Akhlaghi F. Effect of nanosized SiC particles addition to CP Al and Al–Mg powders on their compaction behavior. Powder Technology. 2013;245:126-33.
  23. Poquillon D, Lemaitre J, Baco-Carles V, Tailhades P, Lacaze J. Cold compaction of iron powders—relations between powder morphology and mechanical properties. Powder Technology. 2002;126(1):65-74.
  24. Abdollahi A, Alizadeh A, Baharvandi HR. Dry sliding tribological behavior and mechanical properties of Al2024–5wt.%B4C nanocomposite produced by mechanical milling and hot extrusion. Materials & Design. 2014;55:471-81.
  25. Mosleh-Shirazi S, Hua G, Akhlaghi F, Yan X, Li D. Interfacial valence electron localization and the corrosion resistance of Al-SiC nanocomposite. Scientific reports. 2015;5:18154-.
  26. Razavi Hesabi Z, Sanjari M, Simchi A, Seyed Reihani SM, Simancik F. Effect of Alumina Nanoparticles on Hot Strength and Deformation Behaviour of Al-5vol% Al<SUB>2</SUB>O<SUB>3</SUB> Nanocomposite: Experimental Study and Modelling. Journal of Nanoscience and Nanotechnology. 2010;10(4):2641-5.
  27. Shafiei-Zarghani A, Kashani-Bozorg SF, Gerlich AP. Strengthening analyses and mechanical assessment of Ti/Al2O3 nano-composites produced by friction stir processing. Materials Science and Engineering: A. 2015;631:75-85.
  28. Chandrasekhar SB, Sudhakara Sarma S, Ramakrishna M, Suresh Babu P, Rao TN, Kashyap BP. Microstructure and properties of hot extruded Cu–1wt% Al2O3 nano-composites synthesized by various techniques. Materials Science and Engineering: A. 2014;591:46-53.
  29. Qin S, Chen C, Zhang G, Wang W, Wang Z. The effect of particle shape on ductility of SiCp reinforced 6061 Al matrix composites. Materials Science and Engineering: A. 1999;272(2):363-70.
  30. Zhang DL. Processing of advanced materials using high-energy mechanical milling. Progress in Materials Science. 2004;49(3-4):537-60.
  31. Ren X, Peng L, Huang G, Zong R, Xie H, Li J. Effect of Nd on microstructure and properties of 2A70 alloy. Journal of Alloys and Compounds. 2018;731:1014-21.
  32. Mula S, Padhi P, Panigrahi SC, Pabi SK, Ghosh S. On structure and mechanical properties of ultrasonically cast Al–2% Al2O3 nanocomposite. Materials Research Bulletin. 2009;44(5):1154-60.
  33. Zhang Z, Chen DL. Contribution of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites. Materials Science and Engineering: A. 2008;483-484:148-52.
  34. Al-Rubaie KS, Yoshimura HN, Biasoli de Mello JD. Two-body abrasive wear of Al–SiC composites. Wear. 1999;233-235:444-54.