Fabricating Graphite Coated Copper Via Airbrushing

Document Type : UFGNSM Conference

Authors

1 School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran, Iran

2 School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran-Iran

3 School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran, Iran.

Abstract

Airbrushing is a simple, cost-effective, and easy-to-use method for applying thin layer coatings. In this study, the fabrication of a graphite layer using airbrush spraying has been investigated, which requires stable graphite suspensions without any noticeable sedimentation before and while spraying. Aqueous suspensions with different ratios of Polyvinylpyrrolidone (PVP) to graphite were prepared. PVP was used as a surfactant that can disperse graphite particles in water, which also binds graphite particles to the substrate. For testing each suspension's stability, the turbidity of all samples was measured. The test demonstrated a specific ratio of PVP to graphite that makes the suspension most stable, which is 0.3g. A lower or higher amount of PVP was seen to make the stability worse. The sample with 0.3 grams PVP had the lowest sedimentation rate and thus was chosen for spraying. This optimum composition was sprayed on the substrate using an airbrush, and a graphite coat was obtained in the next step. The main application for the graphite-coated thin layer is in Li-ion batteries as a graphite-based anode.

Keywords


  1. Liu D, Zhao Y, Tan R, Tian L-L, Liu Y, Chen H, et al. Novel conductive binder for high-performance silicon anodes in lithium ion batteries. Nano Energy. 2017;36:206-12.
  2. Alias N, Mohamad AA. Advances of aqueous rechargeable lithium-ion battery: A review. Journal of Power Sources. 2015;274:237-51.
  3. Choi S, Kim Y, Yun JH, Kim I, Shim SE. PVP-assisted synthesis of dense silica-coated graphite with electrically insulating property. Materials Letters. 2013;90:87-9.
  4. Higgins TM, Park S-H, King PJ, Zhang C, McEvoy N, Berner NC, et al. A Commercial Conducting Polymer as Both Binder and Conductive Additive for Silicon Nanoparticle-Based Lithium-Ion Battery Negative Electrodes. ACS Nano. 2016;10(3):3702-13.
  5. Singh N, Galande C, Miranda A, Mathkar A, Gao W, Reddy ALM, et al. Paintable battery. Scientific reports. 2012;2:481-.
  6. Tang Y, Mosseler JA, He Z, Ni Y. Imparting Cellulosic Paper of High Conductivity by Surface Coating of Dispersed Graphite. Industrial & Engineering Chemistry Research. 2014;53(24):10119-24.
  7. Choi N-S, Ha S-Y, Lee Y, Jang JY, Jeong M-H, Shin WC, et al. Recent Progress on Polymeric Binders for Silicon Anodes in Lithium-Ion Batteries. Journal of Electrochemical Science and Technology. 2015;6(2):35-49.
  8. Linden D, Reddy T. Handbook of batteries, McGraw-Hill Companies Inc.
  9. Yakimchuk E, Soots R, Antonova I. Stability of graphene suspensions in an aqueous based multi-component medium. Advanced Materials Letters. 2018;9(3):211-5.
  10. Mancillas-Salas S, Reynosa-Martinez AC, Barroso-Flores J, Lopez-Honorato E. Impact of secondary salts, temperature, and pH on the colloidal stability of graphene oxide in water. Nanoscale Adv. 2022;4(11):2435-43.
  11. Koczkur KM, Mourdikoudis S, Polavarapu L, Skrabalak SE. Polyvinylpyrrolidone (PVP) in nanoparticle synthesis. Dalton Transactions. 2015;44(41):17883-905.
  12. Wajid AS, Das S, Irin F, Ahmed HST, Shelburne JL, Parviz D, et al. Polymer-stabilized graphene dispersions at high concentrations in organic solvents for composite production. Carbon. 2012;50(2):526-34.