Grain refinement, Microstructural characterization, and tensile properties of die-cast AZ91 alloy via Lead and Tin additions

Askaran, Mohammadreza; Malekan, Mehdi; Emamy, Massoud; Lotfpour, Mehrab

doi:10.22059/jufgnsm.2019.02.11

Grain refinement, Microstructural characterization, and tensile properties of die-cast AZ91 alloy via Lead and Tin additions

Document Type : Research Paper

Authors

Mohammadreza Askaran

Mehdi Malekan

Massoud Emamy

Mehrab Lotfpour

School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Iran.

10.22059/jufgnsm.2019.02.11

Abstract

Effects of different amounts of lead (Pb) and tin (Sn) on microstructure and tensile properties of the AZ91 alloy were studied. The results presented that the microstructure of AZ91 alloy is consisted the α-Mg phase and semi-continuous network of β-Mg₁₇Al₁₂ intermetallics. For the as-cast AZ91 alloy, the average grain siz and the β phase volume fraction were 96.2 µm and of 25.3%, respectively. By adding 1 wt.% Pb and 0.5 wt.% Sn, the lowest grain size and volume fraction values obtained. Exceeding Pb and Sn additions have been led to the increasing of the grain size. Furthermore, Sn additions formed the Mg₂Sn intermetallic, while Pb additions didn’t form any obvious intermetallics. The Ultimate Tensile Strength (UTS) and tensile elongation (%El) values of the cast AZ91 alloy were 129 MPa and 2.7%, respectively. The optimum amounts of UTS and %El values were achieved by adding 1 wt.% Pb and 0.5 wt.% Sn, respectively. More Pb and Sn additions deteriorated the tensile properties. The fracture surface observations showed that fracture mode in the cast AZ91 alloy was cleavage. Moreover, 1 wt,% Pb and 0.5 wt.% Sn additions altered the fracture mode to more quasi-cleavage fracture.

Keywords

AZ91 cast alloy

Microstructure

Tensile properties

Grain Refinement

1. Ali Y, Qiu D, Jiang B, Pan F, Zhang M-X. Current research progress in grain refinement of cast magnesium alloys: A review article. Journal of Alloys and Compounds. 2015;619:639-51.

2. Pan F, Yang M, Chen X. A Review on Casting Magnesium Alloys: Modification of Commercial Alloys and Development of New Alloys. Journal of Materials Science & Technology. 2016;32(12):1211-21.

3. Lin H, Yang M, Tang H, Pan F. Effect of minor Sc on the microstructure and mechanical properties of AZ91 Magnesium Alloy. Progress in Natural Science: Materials International. 2018;28(1):66-73.

4. Suresh M, Srinivasan A, Ravi KR, Pillai UTS, Pai BC. Influence of boron addition on the grain refinement and mechanical properties of AZ91 Mg alloy. Materials Science and Engineering: A. 2009;525(1-2):207-10.

5. Guangyin Y, Yangshan S, Wenjiang D. Effects of bismuth and antimony additions on the microstructure and mechanical properties of AZ91 magnesium alloy. Materials Science and Engineering: A. 2001;308(1-2):38-44.

6. Zhang D, Zhang D, Bu F, Li X, Guan K, Yang Q, et al. Effects of minor Sr addition on the microstructure, mechanical properties and creep behavior of high pressure die casting AZ91-0.5RE based alloy. Materials Science and Engineering: A. 2017;693:51-9.

7. Wu G, Fan Y, Gao H, Zhai C, Zhu YP. The effect of Ca and rare earth elements on the microstructure, mechanical properties and corrosion behavior of AZ91D. Materials Science and Engineering: A. 2005;408(1-2):255-63.